Lexus GX 460 Apple CarPlay Install: Keep the Factory Screen

Adding Lexus GX 460 Apple CarPlay does not mean ripping out the factory screen, and it does not mean living with a phone mount on the dash. We installed our Lexus USA approved S-Connect kit in a 2019 GX 460 with factory navigation in one sitting, and the truck came out the other side with wireless CarPlay, Android Auto, the factory backup camera and the steering wheel buttons all working on the original touchscreen.

Short answer: a 2014 to 2021 Lexus GX 460 with factory navigation takes the LGVIF-CB4W wireless CarPlay and Android Auto kit. It plugs in behind the factory screen with no cutting, and you hold the NAV button to switch between CarPlay, Android Auto and the Lexus system.

Which GX 460 Apple CarPlay Kit Fits Your Truck

The GX 460 ran two generations of factory navigation, and the kit is different for each. Check your year before you order:

  • 2014 to 2021 GX 460 with factory navigation: LGVIF-CB4W, the kit in this video.
  • 2016 to 2018 Toyota Land Cruiser with factory navigation: also LGVIF-CB4W.
  • 2010 to 2013 GX 460 with factory navigation: a different kit, the LGVIF-CB8W. Our LGVIF-CB8W configuration guide covers that one.

One more check that catches people: the CB4W needs a single USB system. If your truck has the dual USB ports in the armrest, it is not compatible. If you are not sure which setup you have, our Lexus CarPlay compatibility guide walks through it, and the full lineup sits in our Lexus CarPlay and Android Auto kits collection.

How to Install Lexus GX 460 Apple CarPlay, Step by Step

You need a plastic panel removal tool, a 10 mm socket and a blanket to protect the interior. No splicing, no new head unit. The video chapters line up with the steps below.

Step 1: Open up the center dash

Pull the shift boot down and unscrew the shift knob. Pull the two side bolsters straight toward you. Lift out the cup holder insert, separate its two pieces and unplug the small connector underneath. Set the parking brake, then pull the shifter trim straight back (the clips run that direction), use the shift lock release to move into neutral, and tilt the panel up to unplug its connectors.

Next come the small cover panel, the passenger side dash trim and the vent, all held by clips. Pry out the start button panel. Then remove the 10 mm bolts that hold the center stack.

Step 2: Pull the radio and the screen

Lay the blanket down. Pull the radio straight out and work it toward you slowly. Pull the factory screen the same way and release the connectors on its back.

Step 3: Plug in the harness and video cables

The main harness ships set up for the vehicle you select when you order, so it should go straight in. Unlock the factory main connector with your trim tool, connect one end of our harness to the vehicle side and the other to the radio, and push the locking clips down until they seat.

The two blue GVIF cables carry the video signal. One end goes to the factory blue connector, the other goes back to the screen.

Step 4: Set the switch and connect the module

On the 2019 GX with factory navigation in our video, the dip switch on the video interface is set to switch 1 ON only. Your module has a label with the setting for your vehicle, so follow that.

This is where people slip up: GVIF OUT goes to the inside connector and GVIF IN goes to the outermost one. Swap them and you get no picture. After that, plug the white connector from the main harness into the module, run the included 90 degree HDMI cable to the wireless module (the right angle end goes on the video interface so the cable does not kink), and connect the module power, microphone input, USB extension and the screw-on wireless antenna.

Step 5: Test before you button it up

Put the truck back in park, turn the ignition on and let the Lexus system reboot. Hold the NAV button to bring up the interface. On an iPhone, go to Settings, General, CarPlay, pick the module from the list and pair. Test everything now, while the dash is still open.

Step 6: Tuck the wires and reassemble

Mount both modules in the space shown in the video, route the blue GVIF cables behind the plastic panel and down to where you can reach them, reinstall the 10 mm bolts and clip the trim back on. Pop the USB extension into its spot so it sits flush.

CarPlay No Sound? Two Fixes From Our Install

Both of these happened on camera, and both took under a minute to fix.

Music plays from the phone, not the speakers

CarPlay audio on this kit runs through the factory Bluetooth. In our test the audio source was off, so music came out of the phone. Hold NAV, open Audio, set the source to Bluetooth audio, then pair your phone to the GX hands-free system in your phone's Bluetooth settings. Turn the phone volume all the way up once it connects, and the sound comes through the truck.

Siri talks, but you cannot hear her

Press and hold the voice button and Siri may answer with no sound. Hold your phone's side button until the Siri bubble appears, then raise the phone volume to max while it is showing. That volume is separate from the music volume. After that, Siri and turn-by-turn directions came through clearly.

What You Keep After the Upgrade

  • The factory touchscreen, with tap, swipe and drag working in CarPlay
  • The factory backup camera
  • Steering wheel volume and track controls
  • The factory microphone for Siri and Google Assistant
  • Phone charging while connected
  • Your factory USB ports for the Lexus system

On our final cold start, the truck showed the Lexus caution screen and then jumped straight into CarPlay, with music resuming on its own. If you are weighing a cable against going wireless, our wired vs wireless CarPlay comparison covers the tradeoffs, since this kit supports both.

Why a Screen-Keeping Kit Beats a Replacement Head Unit

A screen replacement changes the dash for good. This kit sits behind the factory display, so the GX looks the way it left the factory. It is approved by Lexus USA and select Lexus dealerships sell and install it, which matters to owners who plan to keep a GX for a long time. We cover the longer argument in why S-Connect is the gold standard CarPlay retrofit.

Planning more upgrades while the dash is apart? Browse our car camera solutions or our stereo interface kits.

Lexus GX 460 Apple CarPlay FAQ

Does the 2021 Lexus GX 460 have Apple CarPlay from the factory?

No. The 2014 to 2021 GX 460 did not offer CarPlay from the factory. The LGVIF-CB4W adds wireless Apple CarPlay and Android Auto to trucks with factory navigation.

How long does the install take?

Most owners finish in 1 to 3 hours with basic hand tools and our video.

Why is there no sound from CarPlay?

The kit plays CarPlay audio over the factory Bluetooth. Set the audio source to Bluetooth audio, pair your phone to the truck, and turn the phone volume all the way up.

Do I need the AUX harness in the kit?

No. It is optional and only needed if you want to run audio through the factory AUX source. We used Bluetooth audio in this install and left it out.

Does it work on a 2010 to 2013 GX 460?

Not this kit. The 2010 to 2013 GX 460 with factory navigation uses the LGVIF-CB8W.

Would Rather Hand Over the Keys?

If a dash teardown is not how you want to spend a Saturday, bring the GX to our shop in La Mirada, California. We do this install in-house, often the same day. Book a GX 460 CarPlay install with our team and tell us your year and whether you have factory navigation.

Leave a comment

Please note, comments must be approved before they are published