Car DSP Amp Install: GR86 and BRZ Under the Seat
A car DSP amp is the fastest way to fix a GR86 or BRZ that sounds flat, and this one goes in without a single cut wire. We installed the Beat-Sonic Encore X DSP amplifier on a Toyota GR86 with the premium 8 speaker system using the ENX-T106 plug and play DSP amplifier kit, mounted it under the passenger seat, and had the car back together in under an hour.
This is not just an amplifier. A DSP amp adds power and processing together, so instead of only making the factory speakers louder it corrects the tuning of a cabin that was never designed around good sound. The kit arrives pre-tuned for this specific car, and it keeps the factory head unit and the factory speakers.
Get the Right Kit First
There are two kits for this chassis and they are not interchangeable. The ENX-T106 covers the 2022-2027 Toyota GR86 Premium and 2022-2026 Subaru BRZ Limited with the factory 8 speaker system. The ENX-T110 covers the 2022-2027 Toyota GR86 Base and 2022-2026 Subaru BRZ Premium with the factory 6 speaker system. Count your speakers or check your trim before you order, and if you are not sure, email us your year and trim and we will confirm it.
What Is in the Box
Open the kit and you get four things. The amplifier itself, pre-tuned using this car's cabin. A plug and play harness with matching 10 pin and 6 pin connectors. Velcro and double sided tape for mounting. And a USB cable that connects the amplifier to a laptop if you want to move away from the factory tune later.
That last item matters more than it looks. Most owners never touch it, because the shipped tune is built for the GR86 and BRZ interior. If you do change speakers or add a subwoofer down the road, the amplifier follows you instead of becoming the weak link. The same idea runs through the rest of our amplifier lineup.
Getting the Radio Out
Use a plastic panel tool so you do not mark the interior trim.
Step 1: Trim and Glove Box
Pop the side panel piece off first and set it aside. Open the glove box, take hold of the side, and pull it out toward you. There is a Phillips screw to remove, then the glove box lifts free with a finger behind it and a little help from the panel tool.
Step 2: The Center Panel
Work the center panel out carefully and loop it forward rather than yanking it. There is a connector behind it. Disconnect that and the panel comes away, exposing four 10 mm bolts holding the radio.
Step 3: The Radio
Lay a thick towel on the console before you pull the radio, then rest the unit face up on top of it. Behind the radio, down toward the passenger bottom corner, you are looking for two plugs. One is a 10 pin and one is a 6 pin. Those are the only two connections the amplifier touches.
Wiring the Amplifier
Unplug the factory 10 pin and 6 pin. Plug them into the female ends of the DSP harness, then plug the harness male ends into the radio. The connectors are keyed and different sizes, so there is no way to get this backward. Nothing is spliced and the whole job reverses in minutes if you sell the car.
The harness is deliberately long so you can put the amplifier almost anywhere. Route the cable straight down from behind the radio. As you feed it, you will hit a bracket on the way. Reach under the lower panel from the other side, get a finger past that bracket, and catch the wire. Push the radio back into place at that point, but leave the bolts out until the amp is confirmed working.
From there, tuck the run under the plastic along the center console and forward under the passenger seat. Push the connector under the seat rail rather than over it. A harness sitting on a rail gets pinched the first time somebody slides the seat back.
The Switch People Forget
Before you close anything up, check two settings on the amplifier body. The DSP switch must be on. The power mode must be set to high, not ACC. This amplifier turns on by sensing the speaker signal from the factory radio, so on ACC you will get silence and assume the install failed. It is the single most common false alarm on this job.
Confirm audio through all speakers, then finish. Mount the amplifier under the passenger seat with the supplied Velcro plus a little double sided tape, well toward the passenger side and clear of the rail. Slide the seat fully forward and fully back to confirm nothing catches. There are airbag lines and seat wiring under there, and a harness caught in a rail is not a problem you want to find later. Reinstall the trim in reverse order and bolt the radio in.
What Changes When You Turn It On
The factory system in these cars is not short on speakers. It is short on power and control. The ENX-T106 puts 45 watts into each of four channels and runs a 24 bit DSP with a 31 band equalizer, crossovers and time alignment behind it, so the result is not simply louder. Vocals come forward, bass stops disappearing above 50 mph, and the whole image stops sitting in the passenger door.
Because the head unit and speakers stay factory, the car looks completely stock. No visible aftermarket hardware, no new screen, and every steering wheel control and chime still works the way Toyota and Subaru built it. If you want the theory behind that, read what DSP actually does in car audio and our guide to tuning a DSP amplifier. For the same install on a different chassis, see the ENX DSP install on a 2025 Toyota Corolla. You can also see the latest additions in new products.
Common Questions
How long does this install take?
Under an hour for most people. The radio removal is the slowest part, and the electrical side is two plugs.
Do I have to keep the factory speakers?
Yes, and that is the point. The kit is designed to drive and correct the speakers already in the car, so nothing behind the door panels needs to come apart.
Why is there no sound after I install it?
Check the power mode switch on the amplifier. It must be set to high, not ACC. The amplifier turns on by detecting the speaker signal from the factory radio, so ACC leaves it silent.
Which kit do I need for my car?
The ENX-T110 is for the 2022-2027 Toyota GR86 Base and 2022-2026 Subaru BRZ Premium with the factory 6 speaker system. The ENX-T106 is for the 2022-2027 Toyota GR86 Premium and 2022-2026 Subaru BRZ Limited with the factory 8 speaker system.
Can I retune the amplifier myself?
Yes. A USB cable is included so you can connect the amplifier to a laptop and adjust it. It ships pre-tuned for this cabin, so most owners never need to.
Where should the amplifier be mounted?
Under the passenger seat works well on these cars. Keep it toward the passenger side, clear of the seat rail and away from airbag wiring, and test the full range of seat travel before you finish.
Questions About Your Car
Every kit ships from our shop in La Mirada, California, and business day orders go out the same day. If you are not certain whether your GR86 or BRZ has the 6 speaker or the 8 speaker system, reach us through the Beat-Sonic contact page with your year and trim and we will confirm it for you before you buy.